|ELECTRICAL TYPICAL VALUES|
|Module||APSP6-230 / 60||APSP6-235 / 60||APSP6-245 / 60||APSP6-250 / 60|
|Rated Power (Pmax)||230W||235W||245W||250W|
|Tolerance||0 ~ ±3%||0 ~ ±3%||0 ~ ±3%||0 ~ ±3%|
|Rated current (Imp)||7.78A||7.82A||8.12A||8.24A|
|Rated Voltage (Vmp)||29.6V||29.8V||30.2V||30.4V|
|Short Circuit Current (Isc)||8.34A||8.44A||8.78A||8.98A|
|Open Circuit voltage (Voc)||36.80V||36.80V||37.35V||37.35V|
|Module Efficiency (%)||14.4||14.8||15.2||15.4|
|NOCT ( Nominal Operation Temperature)||45º±2ºC|
|Temperature Coefficient||-0.35% / ºC|
|Current Temperature Coefficient||+0.05% / ºC|
|Power Temperature Coefficient||-0.48% / ºC|
|ABSOLUTE MAXIMUM RATING|
|Operating temperature||From -40º to +85º|
|Typical Application||24 V DC|
|Hail Diameter @ 80km/h||Up to 25mm|
|Maximum Series Fuse Rating||15|
|IEC Application Class (IEC 61215)||A|
|Fire Rating (UL 1703)||C|
|Maximum System Voltage||1000 V DC (IEC 61215)
600 V (UL 1703)
|Dimension||1640 × 992 × 35 mm|
|Solar Cells||Polycrystalline 156 × 156mm (60pcs)|
|Front Glass||3.2 mm tempered glass, low iron|
|Frame||Anodized/ Electrophoretic aluminium aloy|
|Junction Box||IP65 / IP67|
|Output Cables||4.0 mm2, symmetrical lengths 900mm|
|Maximum Snow Load||550kg/m2|
|Maximum Wind Load||200km/h|
|Hailstone Impact Test||80km/h for 25mm ice ball|
Dimensions in mm and (inches).
Warrantor: AUSTRALIAN PREMIUM SOLAR PTY LTD. ABN:18152185076
(“APS”) AUSTRALIAN PREMIUM SOLAR
4/29 Bellrick st, Acacia Ridge, QLD, Australia, 4110
Warrantee: Referred to herein as “the Customer” or “the End User”
IMPORTANT NOTICE - STATUTORY CONSUMER RIGHTS (for Australian Consumers only)
The benefits conferred to the Customer by this manufacturer’s warranty are in additional to the consumer guarantees, rights and remedies under the State and Federal consumer protection laws including those prescribed under the Australian Consumer Law which is defined herein as your Statutory Rights.
This warranty does not detract, excluded or limit your Statutory Rights.
Your Statutory Rights entitle you to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
PART A: 12 Years Limited Product Warranty
APS warrants to the Customer that its factory-assembled and supplied solar panels, including the photovoltaic modules (“the PV modules”), frames, brackets, connectors, inverters and cables (“the parts”) are free from defects or failure for a period of twelve (12) years from the Warranty Date.
This warranty covers any and all failures of the PV modules or parts as a result of:
Should any PV modules or parts be found to be defective, APS will repair or replace the defective item at no cost to the Customer. In the unlikely event the PV modules or parts cannot be repaired or replaced, APS will provide a refund of the cost of the PV module or part.
Exception:APS does not warrant a specific output power from the PV Modules under this warranty.
PART B: Guaranteed Peak Power Limited Warranty
12 years Peak Power Limited Warranty: APS warrants that for a period of twelve (12) years from the Warranty Date the power output obtained from the PV Modules supplied shall not be less than 91.2% of the Peak Power tested at the STC.
Should any of the PV Modules fail to provide the power output as warranted as a consequence of defective materials or workmanship, APS shall repair or replace the defective PV Module. Alternatively at its sole discretion, APS may add one or more additional PV Modules to the system to bring the total Peak Power output of the complete system to at least 91.6% of the specified Peak Power.
30 years Peak Power Limited Warranty: APS warrants the for a period of thirty (30) years from the Warranty Date the power output from the PV Modules shall not be less than 80.6% of the Peak Power tested at the relevant STC and specified in the APS specification sheet.
Should any of the PV Modules fail to provide the power output as specified as a consequence of defective materials or workmanship, then APS shall repair or replace the defective PV Module. Alternatively, APS may decide to add one or more additional PV Modules to the system to bring the total Peak Power output of the complete system to at least 80.6% of the specified Peak Power.
Subject to any Statutory Rights, the remedies provided under this PART B shall be the only remedies available pursuant to this PART.
Subject to the proper and timely conduct of maintenance of the PV Modules and the parts, the warranties contained in PART A and PART B may be transferred to another Customer provided the PV Modules remains installed in their original location.
Exclusions and Limitations